|
Item category pH/ORP/Conduct - Controllers/ Transmitters/ Monitors
|
 Description The +GF+ SIGNET 9050CR Conductivity Controller offers modularity easily adaptable to any conductivity or resistivity application. Easy single-point "wet-cal" allows for instant accurate calibration. Programming options include display units and temperature compensation. Outputs can be assigned to any channel or display parameters. Features Two-channel capability µS, mS, K, M, ppm, and percent rejection Up to four relays can be installed DC and/or AC powered Applications Reverse osmosis Demineralization Boiler protection Water and waste treatment systems Groundwater remediation Cooling tower blowdown Resource reclamation Compatibility 2800 Series Conductivity Sensors Click here to purchase sensors Technical Data Operating Range: Conductance: 0.055 to 400,000 µS Resistance: 10 k to 18.3 M (0.055 to 100 µS) must be performed in solution temperatures from 20 to 100 degrees C Temperature: PT-1000, 32 to 212 degrees F (Temperature display and alarming from: 14 to 302°F) Power Requirements: 17 to 30 VDC @ 0.5A max. and/or 90 to 132 VAC or 180 to 264 VAC, 50-60 Hz LCD Display: 4-1/2 digit alphanumeric (upper) 8 digit alphanumeric (lower); 4 relay status annunciators Current Output: 4 to 20 mA, isolated or non-isolated, internally powered (2 of 3 card slots available) Loop impedance: 425 ohm max. Accuracy: +/-0.5% of full scale Voltage Output: 0 to 5 or 0 to 10 VDC, isolated or non-isolated Min. load resistance: 1 k ohm Output isolation: 500 VDC to earth ground (isolated only) Alarm Contacts: Two SPDT relays: 5A @ 30 VDC or 250 VAC max. (2 of 3 card slots available) Hi/Lo/Pulse programmable with adj. hysteresis or pulse rate Two SPST relays: 5A @ 30 VDC or 250 VAC max. Hi/Lo/Pulse programmable with adj. hysteresis or pulse rate Temperature compensation: Programmable 0 to 10% per degree C TDS Conversion Factor: Prog. 0.00 to 3.00µS/ppm (default 2.00) Operating Cond.: Operating temperature: 32 to 130 degrees F Relative humidity: 0 to 95%, non-condensing Accuracy: +/-2% of reading Materials: Enclosure: ABS Plastic, NEMA 4X/IP65 Panel and case gasket: Neoprene Immunity: IEC 801-2 level 4, IEC 801-3 level 1 Accessories 3-9000.450-1 0/4 to 20 mA non-iso output card 3-9000.450-2 0 to 5 VDC non-iso output card 3-9000.450-3 0 to 10 VDC non-iso output card 3-9000.460-1 0/4 to 20 mA iso output card 3-9000.460-2 0 to 5 VDC iso output card 3-9000.460-3 0 to 10 VDC iso output card 3-9000.440-1 2 relay card 3-9000.400-1 Dual Proportional relay card 3-5000.395 Splashproof Back Cover Kit 3-5000.598 Mounting Bracket 3-5000.399 Retrofit Adapter Kit 3-9000.392 Liquid Tight Connector Kit Please call 1-800 783 6664 for accessories Model 3-9050CR.1 Cond./Resistivity Controller 110VAC 3.9040.121 Cond./Resistivity Controller 220 VAC Please select from the drop down menu below © 2006 Omni Controls, Inc.. All Rights Reserved. Email: Sales@Omnicontrols.com We guarantee a 24 hour response on all inquiries made via email. For quicker response please call Omni Controls at any of the above numbers |